『FAS2240-4』SP(Service Processor)Firmware 降版本

『FAS2240-4』ONTAP 8.2.5 降版至 8.1.4P1 降版完成後

系統會跳出警示訊息,說我們目前使用的 SP firmware 2.2.4 不相容於 ONTAP 8.1.4P1

Mon Apr 9 14:51:32 CST [FAS2240:sp.firmware.incompatible:warning]: The SP firmware version 2.2.4 is not compatible with this version of Data ONTAP.

原廠查詢後,ONTAP 8.1.4P1 最高支援 SP firmware 2.1.3P2

實際操作後,降 Firmware 版本建議使用 SSH 遠端登入 SP 直接更新(於 ONTAP 中更新會持續遇到 timeout 的問題,並且耗時很久)

查詢 SP IP Address
FAS2240-4-1> sp status
 Service Processor Status: Online
 Firmware Version: 2.2.4
 Mgmt MAC Address: 00:A0:98:3D:04:4C
 Ethernet Link: up, 100Mb, full duplex, auto-neg complete
 Using DHCP: yes
 IPv4 configuration:
 IP Address: 192.168.5.64
 Netmask: 255.255.255.0
 Gateway: 192.168.5.254
 IPv6 configuration: Disabled

可得知目前的 SP Firmware 版本文 2.2.4,IP Address 為 192.168.5.64

登入 SP
ssh naroot@192.168.5.64

使用者 naroot 只能用來登入 sp,密碼與 root 相同

更新 Firmware

此處需先準備好 Firmware 於 HTTP server

SP FAS2240-4-1> sp update //192.168.1.219/Gphoto/306-03097-A0-FAS22XX_2.1.3P2_SP_FW.tar.gz
Downloading package...
Uncompressing package...(md5sum=685798e1f0f368e71d06f260b25bf70f)
Unarchiving package...
Inspecting firmware...
Installing package...
Reprocessing configuration state...
Cleaning up...
SP FW Update Successful.
Use "sp reboot" command to reboot into the new firmware.
重新啟動 SP
SP FAS2240-4-1> sp reboot
The Service Processor will be rebooted. Continue? [y/n] y

Connection to 192.168.5.64 closed by remote host.

重新啟動後再次使用 sp status 查詢,可以確認 Firmware Version 已經降為 2.1.3P2 了!

 FAS2240-4-1> sp status
 Service Processor Status: Online
 Firmware Version: 2.1.3P2
 Mgmt MAC Address: 00:A0:98:3D:04:4C
 Ethernet Link: up, 100Mb, full duplex, auto-neg complete
 Using DHCP: yes
 IPv4 configuration:
 IP Address: 192.168.5.64
 Netmask: 255.255.255.0
 Gateway: 192.168.5.254
 IPv6 configuration: Disabled

參考資料

NetApp® Service Processor 2.1.3P2 Firmware Download and Installation Instructions Using the Service Processor Command Line Interface (CLI)

載入 Firmware 檔
FAS2240> software install 306-03097-A0-FAS22XX_2.1.3P2_SP_FW.zip
software: You can cancel this operation by hitting Ctrl-C in the next 6 seconds.
software: Depending on system load, it may take many minutes
software: to complete this operation. Until it finishes, you will
software: not be able to use the console.
software: installing software, this could take a few minutes...
software: installation of 306-03097-A0-FAS22XX_2.1.3P2_SP_FW.zip completed.
Please type 'sp update' to load the new SP firmware.
更新 SP Firmware

FAS2240> sp update
Updating the SP firmware.
Please ensure you have run ‘software install’ command with correct parameters for ‘sp update’ prior to this step.
DO NOT reset this system during this process.
New SP version : 2.1.3P2
Current SP version : 2.2.4
Sending files to SP

 

Leave A Comment?